C型鋼廣泛應用于鋼結構建筑檁條、墻梁等，也可自組裝成輕型屋面框架、支架等建筑構件，C型鋼安裝需要調整一些部位，哪些部位需要調整?下面濟南C型鋼廠為您分析：

C-shaped steel is widely used in steel structure building purlins, wall beams, etc. It can also be self-assembled into lightweight roof frames, brackets, and other building components. Some parts of C-shaped steel installation need to be adjusted, and which parts need to be adjusted? Below, Jinan C-beam Steel Factory will analyze for you:

1、調整垂直輪。

1. Adjust the vertical wheel.

2、按照a面調整方法，依次調整6-9個通道;

2. Adjust 6-9 channels in sequence according to the A-side adjustment method;

3、調整第五個滾輪通過改變間隔套，以滿足所需的大小。中間左右;

3. Adjust the fifth roller by changing the spacer to meet the required size. Middle left and right;

4、帶材軋制通過一排軸后，調整一軸上的兩輪，使邊緣軋制達到要求(1.5-50px);

4. After the strip passes through a row of shafts, adjust the two wheels on one shaft to make the edge rolling meet the requirements (1.5-50px);

5、間隙調節:根據帶鋼的厚度，用塞子調節每排軸上下輪之間的間隙，使之達到要求的距離;

5. Gap adjustment: According to the thickness of the strip steel, use plugs to adjust the gap between the upper and lower wheels of each row of shafts to achieve the required distance;

6、調整喂料垂直輪(整平軸前后各一對)，使喂料平整、平整，帶鋼平直。將軋制后的帶材平整成一排軸;

6. Adjust the feeding vertical wheels (one pair at the front and one pair at the back of the leveling shaft) to ensure that the feeding is flat and even, and the strip steel is straight. Flatten the rolled strip into a row of shafts;

7、啟動機器使帶鋼在兩軸上軋輥，調整兩軸的兩個輪子，使兩輪子的外緣與一軸的壓痕重合，確保兩輥壓痕前后一致;

7. Start the machine to roll the strip steel on both axles, adjust the two wheels on both axles to make the outer edges of the two wheels coincide with the indentation on one axle, and ensure that the indentation on both rollers is consistent before and after;

8、基準面:用尺子在輪軸和后輪(13道)的同一端測量垂直板的尺寸。使數據相同。然后用尺子測量兩軸兩端和底梁的尺寸，使數據相同;

8. Reference plane: Use a ruler to measure the dimensions of the vertical plate at the same end of the axle and rear wheel (track 13). Make the data identical. Then use a ruler to measure the dimensions of both ends of the two axes and the bottom beam, so that the data is the same;

9、調直調平:在一根軸和下一根軸的兩端用細線制作，其余11根軸與這兩根軸調平。在細線前后做準中線，調整其他11個輪子，使它們都在同一中線上。

9. Straightening and leveling: Make thin wires at both ends of one shaft and the next shaft, and level the other 11 shafts with these two shafts. Align the centerline before and after the thin line, and adjust the other 11 wheels to make them all on the same centerline.

雖然c型鋼有許多優點，但安裝過程中的注意事項尤為重要。c型鋼的安裝將直接影響工程質量，因此安裝需要嚴格按照操作流程進行。更多相關事項就來我們網站http://www.bftlatvia.com咨詢吧！

Although C-shaped steel has many advantages, precautions during installation are particularly important. The installation of C-shaped steel will directly affect the quality of the project, so the installation needs to be strictly carried out in accordance with the operating procedures. For more related matters, come to our website http://www.bftlatvia.com Consult!